Rigol DSG3000 Series Guía de usuario Pagina 111
- Pagina / 144
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 3 Remote Control RIGOL
DSG3000 User’s Guide 3-5
Control Via LAN
1. Connect the devices
Connect the RF signal generator to your LAN using network cable.
2. Configure LAN parameters
Set the LAN parameters of the RF signal generator according to the description
in “I/O Config LAN”.
3. Search device resource
Start-up Ultra Sigma and click
, then click in the
pop-up window, the software starts seaching the RF signal generator resources
connected to LAN. Instrument resources seached will be displayed in the right of
the window. Select your desired resource and click
, as shown in the
following figures.
(a)
(b)
Figure 3-3 Search LAN resource
NOTE: The resource selected should keep consistency with IP address of the
DSG3000 LAN interface.
- User’s Guide 1
- Guaranty and Declaration 3
- Safety Requirement 4
- DSG3000 User’s Guide III 5
- Safety Terms and Symbols 6
- DSG3000 User’s Guide V 7
- VI DSG3000 User’s Guide 8
- DSG3000 User’s Guide VII 9
- General Care and Cleaning 10
- Environmental Considerations 10
- DSG3000 Series Overview 11
- Document Overview 12
- Manuals of this Product 13
- Contents 14
- RIGOL 15
- DSG3000 User’s Guide XIII 15
- XIV DSG3000 User’s Guide 16
- Chapter 1 Quick Start 17
- General Inspection 18
- Appearance and Dimensions 19
- RIGOL Chapter 1 Quick Start 20
- 1-4 DSG3000 User’s Guide 20
- Front Panel Overview 21
- 1-6 DSG3000 User’s Guide 22
- 1-8 DSG3000 User’s Guide 24
- Chapter 1 Quick Start RIGOL 25
- DSG3000 User’s Guide 1-9 25
- DSG3000 User’s Guide 1-11 27
- Rear Panel Overview 28
- DSG3000 User’s Guide 1-13 29
- DSG3000 User’s Guide 1-15 31
- To Connect the Power Supply 33
- Power-on Inspection 34
- To Set the System Language 34
- To Replace the Fuse 35
- User Interface 36
- DSG3000 User’s Guide 1-21 37
- Parameter Zoom-in Mode 39
- DSG3000 User’s Guide 2-1 41
- Frequency 42
- Frequency Offset 42
- Phase Offset 43
- Amplitude 44
- Amplitude Limit 44
- Amplitude Offset 45
- Attenuation Mode 46
- Attenuation 46
- Hold Mode 47
- Flatness Calibration 47
- 2-8 DSG3000 User’s Guide 48
- Amplitude Unit 49
- Sweep Manner 50
- Sweep Direction 50
- Sweep Type 51
- Step Sweep 53
- Sweep Mode 55
- Trigger Mode 56
- Single Sweep 56
- Reset Sweep 56
- DSG3000 User’s Guide 2-17 57
- To Set the Modulation Depth 60
- DSG3000 User’s Guide 2-21 61
- Frequency Modulation (FM) 62
- DSG3000 User’s Guide 2-23 63
- Phase Modulation ( 64
- To Set the Phase Deviation 65
- Pulse Modulation 66
- To Select the Pulse Mode 67
- To Set the Pulse Period 67
- To Set the Pulse Width 67
- Pulse Width 68
- To Select the Trigger Mode 69
- External Gated Signal 70
- Pulse Modulating Signal 70
- Trigger Delay 71
- To Set the Polarity 71
- Pulse Train List 71
- DSG3000 Firmware and Options 72
- Installation Instruction 72
- DSG3000 User’s Guide 2-33 73
- To Enable I/Q Modulation 74
- Baseband Signal 75
- DSG3000 User’s Guide 2-37 77
- LF Output 79
- To Select the LF Waveform 80
- To Set the LF Amplitude 80
- To Set the LF Frequency 80
- Sweep-Sine Waveform 81
- DSG3000 User’s Guide 2-43 83
- To Enable the Power Meter 84
- Zero Type 85
- Frequency Mode 85
- Average Measurement 86
- Limit Measurement 86
- Maximum Limit 87
- Minimum Limit 87
- Recorder 88
- Relative Measurement 89
- Statistics 89
- System Information 90
- RX1000 (Option) 91
- Store and Recall 92
- DSG3000 User’s Guide 2-53 93
- DSG3000 User’s Guide 2-55 95
- DSG3000 User’s Guide 2-57 97
- To Create a Directory 98
- Filename Prefix 99
- Disk Management 99
- System Update 99
- To Set the System Parameters 100
- I/O Configuration 101
- Display Setting 103
- Power Status 103
- Information 103
- License 104
- Self-test 105
- Sanitation 105
- Chapter 3 Remote Control 107
- Remote Control Overview 108
- Control Via USB 109
- Programming Guide 110
- Control Via LAN 111
- 3-6 DSG3000 User’s Guide 112
- DSG3000 User’s Guide 3-7 113
- Control Via GPIB 114
- DSG3000 User’s Guide 3-9 115
- DSG3000 User’s Guide 4-1 117
- To Output RF Signal 118
- To Output RF Sweep Signal 119
- 4-4 DSG3000 User’s Guide 120
- DSG3000 User’s Guide 4-5 121
- Pulse Train Application 122
- DSG3000 User’s Guide 4-7 123
- Chapter 5 Troubleshooting 125
- 5-2 DSG3000 User’s Guide 126
- DSG3000 User’s Guide 5-3 127
- 5-4 DSG3000 User’s Guide 128
- Chapter 6 Specifications 129
- Specifications 130
- DSG3000 User’s Guide 6-3 131
- 6-4 DSG3000 User’s Guide 132
- DSG3000 User’s Guide 6-5 133
- Modulation 134
- DSG3000 User’s Guide 6-7 135
- 0.5VrmsQI 136
- DSG3000 User’s Guide 6-9 137
- Inputs and Outputs 138
- General Specifications 139
- Chapter 7 Appendix 141
- Appendix B: Warranty 142
- Index RIGOL 143
- DSG3000 User’s Guide 1 143
- RIGOL Index 144
- 2 DSG3000 User’s Guide 144
Relacionado con productos y manuales para De medición, control y control Rigol DSG3000 Series
(262 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales